Go Back   Eurocardsharing > Sharing receivers > Technomate > Tutorials

Tutorials Discussion, TM1500CI+ SSSP and GBox at Technomate forum; I found an interesting tutorial about SSSP in another forum. I tried to configure gbox (the one which cames with ...

LinkBack Thread Tools Display Modes
TM1500CI+ SSSP and GBox
Junior Member
jart's Avatar
Posts: 3

Level: 1 [♥ Bé-Yêu ♥]
Life: 0 / 2
Magic: 1 / 73
Experience: 10%

Thanks: 0
Thanked 0 Times in 0 Posts
Join Date: Jul 2007
TM1500CI+ SSSP and GBox - 22-July-2007, 22:30

I found an interesting tutorial about SSSP in another forum. I tried to configure gbox (the one which cames with sharemax - sgbox) and managed to have my TM1500CI+ speaking with sgbox.

Unfortunally, I haven't internet near my box and any D line to test it.

I expect that anyone can test this gbox protocol...

SSSP – Simple Serial Sharing Protocol

This Protocol defines the communication between a DVB Box and a gbox by using a RS232(serial/com/tty port) with only 4 commands to implement.

RS232 communication settings
115200 8N1 (115200 Baud, 8 data bits, no parity, 1 stop bit)

To activate add in the gbox_cfg R: { 01 } for com1, or R: { 02 } for com2
W: and V: should be deactivated 00 00

When developing Software you can activate thers232 debug messages by adding 10 to the R: parameter, a example for com1 would be R: { 11 }

Format of data
AB CD EF GH ....

AB = Command
CDEF = length of the data following
GH ... = data

Total length is CDEF + 3 (1 byte command + 2 bytes len)

Command 0x means from STB to gbox
Command Fx means from gbox to STB

SEND PMT = 01 (send PMT to gbox)
01 xx xx yy yy zz zz zz zz data ....
xx = Len
yy = SID ( byte 2 and bytes 3 from the PMT)
zz = PMT CRC32 (last 4 bytes in the PMT)
Data = CAID1 (2 bytes) PID1 (2 bytes) PROVIDER1 (3 bytes) CAID2 PID2 PROVIDER2 ....
Provider is only used in Seca and Viaccess, in other systems put 00 00 00
For Seca use 00 xx yy and for viaccess xx yy z0

On each channel change the DVB box must send the PMT first, on FTA Channels please send: 01 00 06 yy yy zz zz zz zz

SEND ECM = 03 (send ECM to gbox)
03 xx xx yy yy ecm_data ....
xx = len
yy = pid

Note: Please send every ecm only once, do not send the same ecm multiple times.

REQUESTING PIDS DATA = F1 (receive ECM pid list )
F1 xx xx pid1 pid2 pid3 ....
xx = Len
pidx = 2 bytes for each pid

Please send me ECM data from these pids only, close all other already open.

CW RETURN = F2 (receive ControlWords)
F2 00 10 cw1 (8 bytes) cw2 (8 bytes)

Command flow on a channel change
1. DVB box sends PMT with command 01 on a channel change
2. gbox sends pid list of the ecm's it can handle with command F1
3. DVB box sends ECM's (from all pids in the pid list) with command 03
4. gbox sends CW's with command F2
5. As soon the gbox has success in decoding a ecm it sends again a F1 command with one pid only, the DVB box should close then all other pids and from now on send only ecm data from that pid.

After this command 03 and F2 will be repeated until a channel change.

On the next channel change the DVB should close all open pids and repeat the above procedure.
Reply With Quote
Junior Member
rowlystravel's Avatar
Posts: 21

Level: 3 [♥ Bé-Yêu ♥♥ Bé-Yêu ♥]
Life: 0 / 57
Magic: 7 / 1565
Experience: 31%

Thanks: 3
Thanked 0 Times in 0 Posts
Join Date: Jul 2007
27-July-2007, 17:09

technomate only works with WSP not gbox compatible
Reply With Quote
Sponsored Links
robburne's Avatar
Posts: n/a

Level: 1 [♥ Bé-Yêu ♥]
Life: 0 / 0
Magic: 0 / 0
Experience: 0%

Warn: (0%)
27-August-2007, 15:06

What about the TM9100 - does that only work wiht WSP, what about GBox?


Reply With Quote
Could you help to check it again?
Junior Member
work2008's Avatar
Posts: 2

Level: 1 [♥ Bé-Yêu ♥]
Life: 0 / 0
Magic: 0 / 14
Experience: 2%

Thanks: 0
Thanked 1 Time in 1 Post
Join Date: Sep 2009

Smile Could you help to check it again? - 30-September-2009, 02:57


I try to do it step by step ,but i cannot get the any feedback,i think it's the internet problems,could you confirm that i neednot to set the IP address and other gateway ,subway address?

Thank & BestRegards

Reply With Quote
The Following User Says Thank You to work2008 For This Useful Post:
sideded (01-March-2010)


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

ECS on RSS ECS on Twitter ECS on Facebook ECS on Youtube
Follow us on:

Powered by vBulletin
Copyright 2002 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO ©2011, Crawlability, Inc.