Eurocardsharing

Go Back   Eurocardsharing > Sharing receivers > Technomate > Chat

Chat Discussion, 0963 CCcam2.1.3 Card Resets after 10ecm at Technomate forum; I am using CCcam 2.1.3 with SlyUk 0963 in a TM9100. The card can be read in both slots ( ...

Reply
 
LinkBack Thread Tools Display Modes
0963 CCcam2.1.3 Card Resets after 10ecm
Old
  (#1)
tomslick
Senior Member
 
tomslick's Avatar
 
Offline
Posts: 100

Level: 9 [♥ Bé-Yêu ♥]
Life: 0 / 200
Magic: 33 / 5776
Experience: 0%

Thanks: 44
Thanked 49 Times in 30 Posts
Join Date: Apr 2008
0963 CCcam2.1.3 Card Resets after 10ecm - 27-January-2010, 19:05

I am using CCcam 2.1.3 with SlyUk 0963 in a TM9100. The card can be read in both slots ( I can see entitlements ) and it will open all it's channels. But after about 7-10 ecm/decodes the card restarts and the ecm count goes to 0(0) from 8(8) and then decodes from network ignoring my card. I've used all types of cccam.config with/without boxkey etc. I have used it on two different TM9100 with two different Vaild subscriptions with the same problems after 7-10ecm card gone.

Any suggestions welcome

Tomslick
   
Reply With Quote
The Following User Says Thank You to tomslick For This Useful Post:
spoilerx (29-January-2010)
Old
  (#2)
Hadesuk
Special Friends
 
Hadesuk's Avatar
 
Offline
Posts: 303

Level: 16 [♥ Bé-Yêu ♥]
Life: 0 / 381
Magic: 101 / 9480
Experience: 27%

Thanks: 96
Thanked 422 Times in 154 Posts
Join Date: Aug 2009
Location: UK
30-January-2010, 23:53

Have you tried using your card in another receiver/card reader?
Can you try another card in your receiver?

It might be something to do with the voltage on the internal readers. I believe they are +5v and the new SKY card is +3.3v. Whilst it will work and probably for a while it will die alot earlier than being used in an external reader like an Omnikey.

Hope it points you in the right direction.


Hadesuk





There are 10 types of people in the world: those who understand binary, and those who don't.....
   
Reply With Quote
The Following User Says Thank You to Hadesuk For This Useful Post:
tomslick (31-January-2010)
Sponsored Links
Old
  (#3)
BigG
Donator
 
BigG's Avatar
 
Offline
Posts: 16

Level: 2 [♥ Bé-Yêu ♥♥ Bé-Yêu ♥]
Life: 0 / 43
Magic: 5 / 1211
Experience: 74%

Thanks: 19
Thanked 5 Times in 5 Posts
Join Date: Aug 2008
04-February-2010, 13:39

I had the same problem with the 0963 card try setting the frequency for the card in CCCam.cfg:
SMARTCARD CLOCK FREQUENCY: /dev/{your reader} 3570000

Alternatively, read the card in NewCS then share with CCCam - I have found this to be the most stable solution.

Cheers,
BigG


1 x TM9100
2 x DM500
1m Triax, 3 Quad LNB (13,19,28 East)
3 x DiSEqC Switch
Linux CCCam Server on 10MB Ethernet
   
Reply With Quote
The Following User Says Thank You to BigG For This Useful Post:
tomslick (04-February-2010)
Old
  (#4)
newtolinux
Member
 
newtolinux's Avatar
 
Offline
Posts: 92

Level: 8 [♥ Bé-Yêu ♥]
Life: 0 / 189
Magic: 30 / 5433
Experience: 57%

Thanks: 4
Thanked 21 Times in 19 Posts
Join Date: Apr 2008
04-February-2010, 16:03

card does not read direct in slot on tm9100 unless you use newcs to read and pass to cccam. This will make the card stable . You could add 256 at end of n line in cccam so card appears local still. hope that helps .
   
Reply With Quote
The Following User Says Thank You to newtolinux For This Useful Post:
tomslick (04-February-2010)
Old
  (#5)
pipebender
Junior Member
 
pipebender's Avatar
 
Offline
Posts: 12

Level: 2 [♥ Bé-Yêu ♥]
Life: 0 / 31
Magic: 4 / 787
Experience: 25%

Thanks: 1
Thanked 1 Time in 1 Post
Join Date: Jul 2009
21-April-2010, 02:01

i got the same problem. changed the freq to 3570000 and now it resets at 90 ecms. every time it resets i get a pause in the picture. im using a TM600 with cccam 2.1.4. any help appreciated.
   
Reply With Quote
Old
  (#6)
balderdash
Member
 
balderdash's Avatar
 
Offline
Posts: 60

Level: 6 [♥ Bé-Yêu ♥♥ Bé-Yêu ♥♥ Bé-Yêu ♥♥ Bé-Yêu ♥]
Life: 0 / 140
Magic: 20 / 3286
Experience: 62%

Thanks: 16
Thanked 12 Times in 12 Posts
Join Date: Feb 2010
21-April-2010, 10:27

Quote:
Originally Posted by pipebender View Post
i got the same problem. changed the freq to 3570000 and now it resets at 90 ecms. every time it resets i get a pause in the picture. im using a TM600 with cccam 2.1.4. any help appreciated.
You need to use NewCS to read the card and then use CCcam 2.1.4 to share it,

I have heard that the latest UR image,released yesterday I think,fixes this problem and will now happily read and share 0963 cards.
   
Reply With Quote
Reply

Bookmarks

Tags
0963, 10ecm, card, cccam2.1.3, resets


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump



ECS on RSS ECS on Twitter ECS on Facebook ECS on Youtube
Follow us on:

Powered by vBulletin
Copyright 2002 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO ©2011, Crawlability, Inc.
Dreambox