The difference between Quad & Quattro LNB's

**Morte**

Quote:

TECH TIP: Quad LNB v Quattro LNB - what's the difference?

So you are looking to feed a number of locations with a satellite TV signal and you have decided that you need at least four feeds. You've seen that it's possible to by two different types of four output LNB device to fit on your satellite dish, one called a Quad LNB and the other called a Quattro LNB. Confused?
This brief article aims to outline the difference between a quad LNB and a quattro LNB, plus give a few practical examples of why you may choose one over another.
What is an LNB?

First we need to cover a bit of background on what an LNB actually does. LNB stands for Low Noise Block Downconvertor and sometimes they are just called Downconvertors. The word downconvertor conveys what an LNB actually does - it converts high frequencies down to lower frequencies. This 'downconversion' is required to enable a satellite receiver to decode the signal into video and audio. The frequencies transmitted by a satellite are too high to be decoded by a set-top box.
Satellite receivers are capable of receiving a number of different signal bands and a 'universal' LNB has the ability to receive all of these. It is normal for a universal LNB to receive the following bands:
Low Band - Horizontal Polarisation
High Band - Horizontal Polarisation
Low Band - Vertical Polarisation
High Band - Vertical Polarisation
The LNB is not able to downconvert all of these simultaneously - it needs to be sent commands from the satellite receiver that switch the LNB output to the desired band/polarisation. The satellite receiver switches the universal LNB to receive either High or Low Band with a 22Hz tone and either Horizontal or Vertical Polarisation with a switching voltage between 12.5v - 18v. These tones and voltages are sent up the coaxial cable from the back of the receiver to the output of the LNB.
Quad LNB

The quad LNB provides four outputs, each capable of providing each of the four frequency bands and polarisations. The LNB outputs are switched by the satellite receiver, as explained above, with a 22Hz tone and a switching voltage. This is like a universal LNB with four outputs.
In a simple residential satellite TV installation it is normal to install a quad LNB. In a Sky installation, often two of the outputs from a quad LNB will be used to feed a Sky+ receiver (it has two feeds so you can record while watching live TV), with either the other two feeding a second Sky+ receiver or just a single output feeding a regular Sky box.
A quad LNB is ideal where a maximum of four satellite feeds is required and there is not much possibility of expansion.
Quattro LNB

The quattro LNB provides four outputs, each with a single band/polarization specific to that output. The band/polarization available at each output is fixed at the time of manufacture. It is not possible to switch the band/polarization with a tone or switching voltage.
A quattro LNB is normally used to feed a large distribution system. A single dish with a quattro LNB fitted and a multiswitch (or IRS) is able to feed anything between 4 and 100 locations. The multiswitch (or IRS) is able to provide any of the input signals at each output, depending on a tone/voltage sent up the cable by the receiver at each location. It's as though the receiver at each location has it's own dedicated LNB.
The outputs on a multiswitch (or IRS) are able to be controlled with a 22Hz tone and switching voltages in the same way that the outputs from normal universal LNB can be, i.e. to change band and polarisation. The satellite receivers in each of the locations behave as though they are connected to their own dedicated dish and LNB, but in reality are just connected to a multiswitch (or IRS) output.
Quattro LNBs are considered to have a better lifetime than quad LNBs as they are not being continually switched.

source: hxxp://www.xtendedplay.co.uk

There are nowadays also Octo LNB's which has 8 outputs for 8 receivers or 4 dualtuner receivers

Hardware: DM500S, MaximumTorodial T90, Inverto Silver Tech 0,2 db
Sat positions: 4.8°,13.0°,19.2°,28.2°
Software: Pli Jade 2 with X-line Skin
CAM: Cccam 2.1.2
NOT LOOKING FOR SHARES
[Only Registered Users Can See LinksClick Here To Register]
[Only Registered Users Can See LinksClick Here To Register]
[Only Registered Users Can See LinksClick Here To Register]

Use the ====>>>>

<<<<==== when you are happy with a post instead of replying to a post (rule #11 and gets you even banned)

Last edited by Morte; 06-June-2009 at 10:39.

~~**cetrov2009**~~

Octal LNB's work fine for 8 independent boxes in different apartments. What I dislike about them is that only the first box to connect to the LNB gets to power it up. Obviously this may lead to malfunction on some makes that have a particular LNB input only which caters for power-IN. So please check. I opt for a multiswitch system in cases where more than 4 outputs are needed. They are more stable.