Big Problem Cccam:Peers cannot see me online

I have a problem since 15 days,posted to couple sites,
read ALL the tutorials etc. on the net but could not solve the problem.
I would very much appreciate if someone cares to answer.
I can get channels from my peers flawlessly but they don't see me online.......so they dump me (:
When ı write "me.dyndns.org" into the adress line I get
to the password page of my router.
When adding.. :12000 get no page at all.
-At the check page of dyndns everything seems ok.IP
is right.
-Portforwarding ok.
-Dyndns upgrade is configured in the router.
-Inadyn disabled in Dreambox (when enabled nothing changes)
-I can access the receiver through the router,ftp etc.
-Also Dream to internet perfect.

Below is my cccam cfg.
Maybe this is the culprit ?
-My C line is not on the file.??
I have added a F line to the C line I received from the
peer with the server.
Is this right ?

F: peer.ddinc201hh 3 0 0 { 0:0:3 }
C: peer.dyndns.org 12000 ddinc ddinc201hh no { 0:0:3 }



SERVER LISTEN PORT : 12000

ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME : root
WEBINFO PASSWORD : dreambox
TELNETINFO USERNAME : root
TELNETINFO PASSWORD : xxxxx
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 16001
ZAP OSD TIME :0
OSD USERNAME : root
OSD PASSWORD : bbdmr12
OSD PORT : 80
#SERIAL READER : /dev/tts/0
SHOW TIMING : yes
DEBUG : no
NEWCAMD CONF : yes
DISABLE EMM : yes
EXTRA EMM LEVEL : no
MINI OSD : yes
SOFTKEY FILE : /var/keys/SoftCam.Key
AUTOROLL FILE : /var/keys/AutoRoll.Key
STATIC CW FILE : /var/keys/constantcw
CAID PRIO FILE : /var/etc/CCcam.prio
PROVIDERINFO FILE : /var/etc/CCcam.providers
CHANNELINFO FILE : /var/etc/CCcam.channelinfo
MINIMUM CLIENT VERSION : 1.7.0
B: /dev/sci0 00
B: /dev/sci1 00

That means your STB can access the internet, but not that your peers can access the STB FROM the internet.

Browser to hostname on port 12000 should open an octet stream in your browser if it can read those or prompt to download or open with...

If this does not happen, given that your peers cannot connect to you either, it is nearly certain that port forwarding is NOT set up correctly.

Reaching your router web interface when browsing to your DDNS address at the port 80 default suggests that your router is not configured correctly, or at least that it is not configured very safely.

Your F: Line needs to be in the format Is this a typo?


Your CCcam.cfg as below is fine. None of what is below is actually required, since you have all or most set to the default values. But it is always good to enable the passwords and to make these difficult to guess.

Your problem is most likely at the modem/router level. There is a very small chance your ISP is blocking, but this is much less likely than a misconfigured modem/router.

If you check this and still cannot get it to work, PM me and I will try to set up the router remotely.

Originally Posted by Red Avishay [Only Registered Users Can See LinksClick Here To Register] Hi, I have the same exact problem... using all defaults in CCcam.cfg, when typing the ddns adress with :12000 I get some gybrish line - something like this: רֻb”@«Sf{ז×# which is different from when I add any other port to it. I get the same result when I type the reciever's local ip and add :12000 is there a solution for that? Thanks!

Originally Posted by adamjohn [Only Registered Users Can See LinksClick Here To Register] i have port forwarded my router tcp & udp correctly on port 12000